EnergyMax Aliphatic Polyurethane
Description
EnergyMax Aliphatic Polyurethane is a solvent-based, single component moisture cure polyurethane roof coating. Excellent topcoat for EnergyGuard Aromatic Polyurethane Coating for improved UV-resistance and reflectivity.
Uses
For restoring and extending the life of built-up, concrete, metal, modified bitumen, single-ply (EPDM, TPO) membranes and polyurethane foam.
Benefits
- Provides a seamless, elastic and durable membrane.
- Contains fungicides and mildewcides.
- Superior adhesion to various substrates.
- Reflective roof coating helps reduce cooling costs, prevents UV-degradation and premature roof failure.
- High tensile strength and elongation.
- Excellent protection for polyurethane foam.
Application
- Ready to use. Thinning is not necessary. Mix well before using.
- Roof must be clean, dry and free of any oil, grease, dirt or loosely adhered coating.
- Bare surfaces must be prepared and checked for compatibility.
- Follow our roof restoration procedures and always perform an adhesion test.
- Equipment: polyester brush, long nap roller, spreader or 3000psi, 2gpm airless sprayer with a .017 tip.
- Do not leave coating in spray guns, hoses and pumps for prolonged periods.
Warning: This product contains solvents. Keep away from open flame, heat or sparks. Pumping equipment should be grounded to avoid accidental ignition due to static sparks. Use only in ventilated areas and provide mechanical ventilation in enclosed spaces. Avoid breathing vapor or mist. Approved (MESA/NIOSH) chemical respirator and protective clothing must be used when exposure can exceed recommended PEL. Fresh air hose masks required for interior applications. Care must be taken to prevent rooftop HVAC from introducing solvent vapor into interior areas. Lexis Coatings must be completely dry before exposing to water or foot traffic. Keep Lexis Coatings containers covered when not in use. Dispose of all containers in accordance with state and local environmental regulations. Keep away from children. If ingested, DO NOT induce vomiting. Call physician immediately.
Product information contained herein are presented in good faith and believed to be reliable. They do not constitute part of our terms and conditions of sale. It is also not a guarantee, either expressed or implied, that the data are correct or that products described are merchantable or fit for a particular purpose as methods of use are beyond our control. Customer should determine the suitability of our materials and installation recommendations before usage. Manufacturer’s sole responsibility shall be to replace that portion of any product that proved to be defective.
Technical Data
| Property | Value | Test Method |
|---|---|---|
| Application Temperature | 50°F (and rising) - 95°F. Cure time will be significantly higher below 45°F | |
| Clean Up | Xylene | |
| Color | White | |
| Density | 8.5 ±.2 pounds/gallon | |
| Dry Time | Dry to touch: 3-4 hours Tack Free:12-16 Recoat:12-16 | |
| Emittance | 86% | |
| Elongation | 350% ± 50 | ASTM D-412 |
| Flash Point | 93°F | |
| Hardness | 69 Shore A | ASTM D-2240 |
| Permeability | .02 perms | ASTM E-96 |
| Service Temperature | -50º TO 200º F | |
| Shelf Life | 3 months @ 40°F-90°F | |
| Solids by Volume | 68% | ASTM D-2697 |
| Solids by Weight | 77% | ASTM D-1644 |
| Tensile Strength | 600 ±25 psi | ASTM D-412 |
| Reflectance | 86% | |
| Viscosity | 3000- 3100 cPs | Brookfield |
| Water Absorption | 1.6% |