EnergyGuard Silicone Coating

Product Description

EnergyGuard Silicone Coating is a solvent-based, single component, moisture cure, high solids, silicone roof coating.

Uses

For restoring and extending the life of built-up, concrete, metal, modified bitumen, single-ply (EPDM, TPO) membranes and polyurethane foam.

Benefits

Breathable membrane has exceptional weathering characteristics, prevents moisture entrapment and premature roof failure.Not affected by ponding water.
May be used for potable rainwater catchment applications.Reflective roof coating reduces cooling costs.
An excellent top coat over EnergyGuard Aromatic Polyurethane.
Complies with all of the requirements of ASTM D 6694-08 and -07 Standard Specification Liquid-Applied Silicone Coating and ASTM C1305 Crack Bridging Ability.
WARNING: This product can expose you to chemicals including Quartz and Naphthalene, which is known to the State of California to cause cancer.

Application

Mix thoroughly before using. Thinning not recommended. Mix well before using.
Roof must be clean, dry and free of any oil, grease, dirt or loosely adhered coating.
Bare surfaces must be prepared and checked for compatibility.
Follow our roof restoration procedures and always perform an adhesion test.
Equipment: polyester brush, long nap roller, spreader or 3500psi, 3gpm airless sprayer with a .031 tip.Do not leave coating in spray guns, hoses and pumps for prolonged periods.
Use BUNA-N jacketed hoses for moisture protection. Do not leave coating in spray guns, hoses and pumps for prolonged periods.

Could not load Commerce. Please try again later.

Warning: This product contains solvents. Keep away from open flame, heat or sparks. Pumping equipment should be grounded to avoid accidental ignition due to static sparks. Use only in ventilated areas and provide mechanical ventilation in enclosed spaces. Avoid breathing vapor or mist. Approved (MESA/NIOSH) chemical respirator and protective clothing must be used when exposure can exceed recommended PEL. Fresh air hose masks required for interior applications. Care must be taken to prevent rooftop HVAC from introducing solvent vapor into interior areas. Lexis Coatings must be completely dry before exposing to water or foot traffic. Keep Lexis Coatings containers covered when not in use. Dispose of all containers in accordance with state and local environmental regulations. Keep away from children. If ingested, DO NOT induce vomiting. Call physician immediately.

Product information contained herein are presented in good faith and believed to be reliable. They do not constitute part of our terms and conditions of sale. It is also not a guarantee, either expressed or implied, that the data are correct or that products described are merchantable or fit for a particular purpose as methods of use are beyond our control. Customer should determine the suitability of our materials and installation recommendations before usage. Manufacturer’s sole responsibility shall be to replace that portion of any product that proved to be defective.

Technical Data

Property	Value	Test Method
Clean Up	VM&P Naphtha, Mineral Spirits
Color	White, Gray, Custom
Density	10.3 lbs/gal
Coverage	1.5gal/100SF yields 15.52 dry mils. Up to 1.5gal/100SF per coat. 2 coats, 25-30 mils recommended. NSF Compliance: 15DFT per coat, 3 coats, 45 dry mils required.
Cure Time	Dry to Touch: 6 hours Tack Free: 2 hours Skinover: 30 minutes Recoat: 24 hours @ 100F° / 70% RH. Final Cure: 30 days at 100°F / 70% RH.
Elongation	318% initial	ASTM D-412
Emissivity	0.88 Aged 3 Years (White)	ASTM C-1371
Flash Point	106F°	ASTM D-93
Hardness	55±5 (Shore A)	ASTM D-2240
Permeability	2.1 perms	ASTM E-96
Reflectivity	87%	ASTM C-1549
Shelf Life	12-18 months (Unopened Containers @ 40°F-90°F)
Solids by Volume	67%	ASTM D-2697
Tack Free	2 Hour (Depending on humidity and temperature)
Tensile Strength	500 psi	ASTM D-412
Viscosity	7500 ± 1500 cps	Brookfield
Service Temperature	-50º TO 200º F
Thermal Emittance	88%