EnergyGuard Acrylic Coating
Product Description
EnergyGuard Acrylic Coating is a water-based, single component, acrylic roof coating.
Uses
It can be used to stop roof leaks and extend the service life of metal and spray foam roofs.
Benefits
- Provides a seamless, elastic and durable membrane.
- Contains fungicides and mildewcides.
- Superior adhesion to various substrates.
- Reflective roof coating reduces cooling costs, prevents UV-degradation and premature roof failure.
- Easy to use, non-toxic and VOC-compliant.
Application
- Mix thoroughly before using. Thinning not recommended.
- Mix well before using.Do not use on ponding water locations.
- Roof must be clean, dry and free of any oil, grease, dirt or loosely adhered coating.
- Bare surfaces must be prepared and checked for compatibility.
- Follow our roof restoration procedures and always perform an adhesion test.
- Roofing granules may be introduced within 10 minutes of final coat at a rate of 35-40 lbs/100SF.
- Equipment: polyester brush, long nap roller, spreader or 3000psi, 2gpm airless sprayer with a .031 tip.
- Do not leave coating in spray guns, hoses and pumps for prolonged periods.
Caution: This product is water-based product which will freeze and become unusable at temperatures below 32°F. Suspend all application if conditions prevent a complete cure before sunset, rain, fog, dew or freezing temperatures. Lexis Coatings must be completely dry before exposing to water or foot traffic. Keep Lexis Coatings containers covered when not in use. Dispose of all containers in accordance with state and local environmental regulations. Keep away from children. If ingested, DO NOT induce vomiting. Call physician immediately.
Product information contained herein are presented in good faith and believed to be reliable. They do not constitute part of our terms and conditions of sale. It is also not a guarantee, either expressed or implied, that the data are correct or that products described are merchantable or fit for a particular purpose as methods of use are beyond our control. Customer should determine the suitability of our materials and installation recommendations before usage. Manufacturer’s sole responsibility shall be to replace that portion of any product that proved to be defective.
Technical Data
| Property | Value | Test Method |
|---|---|---|
| Application Temperature | 55°F (and rising) - 100°F. Less than 85% relative humidity. | |
| Algae Resistance | No Growth | ASTM G29-96 |
| Clean Up | Water | |
| Color | White, Gray, Custom | |
| Cure Time | Dry to Touch: 4 hours @ 75°F Tack Free: 12 hours. Recoat: 12 - 24 hours. | |
| Density | 11.4 ±.2 pounds/gallon | |
| Elongation | 315% | ASTM D-412 |
| Emittance | 0.90 | ASTM C-1371 |
| Flash Point | None | |
| Fungi Resistance | No Growth | ASTM G29-96 |
| Hardness | 45 Shore A | ASTM D-2240 |
| Impact Resistance | >160 inch/pounds | ASTM D-2294 |
| Permeability | 3.4 perms | ASTM E-96 |
| Reflectance | 82% | ASTM C-1549 |
| Salt Spray | No Effect (3000 hours) | ASTM B-117 |
| Service Temperature | -40°F to 200°F | |
| Shelf Life | 12 months @ 45°F-80°F | |
| Solids by Volume | 60% ±2% | ASTM D-1644 |
| Solids by Weight | 68% ±2% | ASTM D-1644 |
| Tensile Strength | 400 psi, 3600psi with SeamStitch Fabric | ASTM D-412 |
| Viscosity | 8,000 ±1500 cP | Brookfield |
| Weatherability | No Effect (3800 hours) | ASTM G-26 |