EnergyGuard Aromatic Polyurethane

I. IDENTIFICATION

  • PRODUCT IDENTIFICATION
  • EnergyGuard Aromatic Polyurethane
  • Packaging: Pail, Drum
  • CAS Number: n/a
  • DATE UPDATED
  • Friday, February 16, 2018
  • EMERGENCY TELEPHONE NUMBER
  • INFOTRAC: 800-535-5053

SUPPLIER INFORMATION

Lexis Coatings
  • 6460 Hwy 92 Ste 100
  • Acworth, GA 30102
  • Phone: 770-755-1820
  • Hours: Mon - Fri 8am - 5pm

II. HAZARDS(S) IDENTIFICATION

  • CLASSIFICATION
  • Skin Sens. 1;H317: May cause an allergic skin reaction.
  • Acute Tox 4;H332: Harmful if inhaled.
  • Skin Irrt. 2;H315:Causes skin irritation.
  • Eye Irrt. 2;H319:Causes serious eye irritation.
  • Resp. Sens. 1;H334: May cause allergy or asthma symptoms of breathing diffculties if inhaled.
  • Carc. 2;H351: Suspected of causing cancer.
  • STOT SE 3;H335: May Cause respiratory irritation.
  • STOT RE 2;H373: May Cause damage to organs through prolonged or repeated exposure. Specific Target Organs: (hearing organs)
  • Flam. Liq. 3;H225: Highly Flammable liquid and vapor.
  • LABEL ELEMENTS
  • Using the Toxicity Data listed in section 11 and 12 the product is labled as follows:
Hazard Pictograms
  • Harmful
    Harmful
  • Flammable
    Flammable
  • Health Hazard
    Health Hazard
  • Signal Word: Danger
  • Hazard Statements
  • H225 Highly flammable liquid and vapor.
  • H315 Causes skin irritation.
  • H317 May cause an allergic skin reaction.
  • H319 Causes serious eye irritation.
  • H332 Harmful if inhaled.
  • H334 May cause allergic or asthmatic symptoms or breathing difficulties if inhaled.
  • H335 May cause respiratory irritation.
  • H351 Suspected of causing cancer.
  • H373 May cause damage to organs through prolonged or repeated exposure.
  • [Prevention]
  • P210 Keep away from heat / sparks / open flames / hot surfaces - No smoking.
  • P201 Obtain special instructions before use.
  • P202 Do not handle until all safety precautions have been read and understood.
  • P261 Avoid breathing dust / fume / gas / mist / vapors / spray.
  • P264 Wash thoroughly after handling.
  • P271 Use only outdoors or in a well-ventilated area.
  • P272 Contaminated work clothing should not be allowed out of the workplace.
  • P280 Wear protective gloves / eye protection / face protection.
  • [Response]
  • P302+352 IF ON SKIN: Wash with plenty of soap and water.
  • P304+312 IF INHALED: Call a POISON CENTER or doctor / physician if you feel unwell.
  • P305+351+338 IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do - continue rinsing.
  • P308+313 IF exposed or concerned: Get medical advice / attention.
  • P314 Get Medical advice / attention if you feel unwell.
  • P321 Specific treatment (see information on this label).
  • P333+313 If skin irritation or a rash occurs: Get medical advice / attention.
  • P337+313 If eye irritation persists: Get medical advice / attention.
  • P340 Remove victim to fresh air and keep at rest in a position comfortable for breathing.
  • P341 If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable for breathing.
  • P342+311 If experiencing respiratory symptoms: Call a POISON CENTER or doctor / physician.
  • P362 Take off contaminated clothing and wash before reuse.
  • P363 Wash contaminated clothing before reuse.
  • [Storage]
  • P403+233 Store in a well ventilated place. Keep container tightly closed.
  • P405 Store locked up.
  • [Disposal]
  • P501: Dispose of contents / container in accordance with local / national regulations.

III. COMPOSITION / INFORMATION ON INGREDIENTS

Chemical Name CAS Number Weight% GHS Classification Notes
Xylene 0001330-20-7 10 - 25 Flam. Liq. 3;H226
Acute Tox. 4;H332
Acute Tox. 4;H312
Skin Irrit. 2;H315
[1][2]
Oxirane, methyl-, polymer with
1,1'-methylenebis[isocyanatobenzene]
0157937-75-2 10 -25 Skin Irrit. 2;H315
Skin Sens. 1;H317
Eye Irrit. 2;H319
Acute Tox. 4;H332
Resp. Sens. 1;H334
STOT SE 3;H335
STOT RE 2;H373
Carc. 2;H351
[1]
Isocyanic acid, polymethylenepolyphenylene ester,
polymer with .alpha.-hydro-.omega.-
hydroxypolyoxy(methyl-1,2-ethanediy
0053862-89-8 1.0 - 10 Skin Irrit. 2;H315
Skin Sens. 1;H317
Eye Irrit. 2;H319
Acute Tox. 4;H332
Resp. Sens. 1;H334
STOT SE 3;H335
STOT RE 2;H373
[1]
Diphenylmethanediisocyanate 0000101-68-8 1.0 - 10 Acute Tox. 4;H332
Skin Irrit. 2;H315
Eye Irrit. 2;H319
STOT SE 3;H335
Skin Sens. 1;H317
Resp. Sens. 1;H334
[1][2]
Polymeric Diphenylmethane Diisocyanate 0009016-87-9 1.0 - 10 Acute Tox. 4;H332
Skin Irrit. 2;H315
Eye Irrit. 2;H319
STOT SE 3;H335
Skin Sens. 1;H317
Resp. Sens. 1;H334
[1]
Benzene, 1-isocyanato-2-[(4-isocyanatophenyl)methyl]- 0005873-54-1 1.0 - 10 Carc. 2;H351
Acute tox. 4;H332
STOT RE 2;H373
Eye Irrit. 2;H319
STOT SE 3;H335
Skin Irrit. 2;H315
Resp. Sens. 1;H334
Skin Sens. 1;H317
[1]
Ethyl Benzene 0000100-41-4 1.0 - 10 Flam. Liq. 2;H225
Acute Tox. 4;H332
STOT RE 2;H373
Asp. Tox. 1;H304
[1]
Petroleum distillates, hydrotreated light 0064742-47-8 1.0 - 10 Asp. Tox. 1;H304 [1]
Tosyl isocyanate 0004083-64-1 .10 - 1.0 Eye Irrit. 2;H319
STOT SE 3;H335
Skin Irrit. 2;H315
Resp. Sens. 1;H334
[1]
  • In accordance with paragraph (i) of §1910.1200, the specific chemical identity and/or exact percentage (concentration) of composition has been withheld as a trade secret.
  • [1] Substance classified with a health of enviromental hazard.
  • [2] Substance with workspace exposure limit.
  • [3] PBT-subtance of VpvB-substance.

IV. FIRST-AID MEASURES

Description of first aid measures
General
In all cases of doubt, or when symptoms persist, seek medical attention. Never give anything by mouth to an unconscious person.
Inhalation
Remove to fresh air, keep patient warm and at rest. If breathing is irregular or stopped, give artificial respiration. If unconscious place in the recovery position and obtain immediate medical attention. Give nothing by mouth.
Eyes
Get medical attention immediately.
Skin
Remove contaminated clothing and shoes/boots. Wash affected area with alcohol. Don’t wash with water.
Ingestion
If swallowed obtain immediate medical attention. Keep at rest. Do NOT induce vomiting
Most important symptoms and effects, both acute and delayed
Overview
Exposure to solvent vapor concentrations from the component solvents in excess of the stated occupational exposure limits may result in adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the kidneys, liver and central nervous system. Symptoms include headache, nausea, dizziness, fatigue, muscular weakness, drowsiness and in extreme cases, loss of consciousness.

Repeated or prolonged contact with the preparation may cause removal of natural fat from the skin resulting in dryness, irritation and possible non-allergic contact dermatitis. Solvents may also be absorbed through the skin. Splashes of liquid in the eyes may cause irritation and soreness with possible reversible damage. See section 2 for further details.
Inhalation
Harmful in inhaled. May cause allergy or asthma symptoms of breathing difficulties if inhaled.
Eyes
Causes serious eye irritation.
Skin
May cause an allergic skin reaction. Causes mild skin irritation.

V. FIRE-FIGHTING MEASURES

Extinguishing media
Water, carbon dioxide, foam or dry powder.
Special hazards arising from the substance or mixture
Hazardous decomposition: Will not occur if properly handled and stored. Avoid breathing dust/fume/gas/mist/vapors/spray.
Advice for fire-fighters
Use water spray to cool non-involved containers. Wear SCBA with full-face piece operating in a positive pressure demand mode and full protective gear. This product is considered combustible and is a fire hazard. During a fire isocyanate vapors and other irritating gases may be generated by thermal decomposition or combustion. At temperatures above 137°F it can cause pressure build-up in closed containers. Use cold water to cool fire-exposed containers.
ERG Guide No. 127

VI. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Put on appropriate personal protective equipment (see section 8).
Environmental precautions
Do not allow spills to enter drains or waterways.
Use good personal hygiene practices. Wash hands before eating, drinking, smoking or using toilet. Promptly remove soiled clothing and wash thoroughly before reuse.
Methods and material for containment and cleaning up
Shut off ignition sources including electrical equipment and flames. Contain spilled material. Absorb spills with inert material such as vermiculite, dry sand or earth. Place in a closed container but do not seal. Ventilate area to remove vapors.

VII. HANDLING AND STORAGE

Precautions for safe handling
Avoid prolonged or repeated skin contact. Avoid breathing aerosols, spray mists, and heated vapors. Use only in well ventilated area. Use good personal and industrial hygiene practices.
Keep container closed after each use.
See section 2 for further details. - [Prevention]:
Conditions for safe storage, including any incompatibilities
Handle containers carefully to prevent damage and spillage.

Precautions should be taken to minimize exposure to atmospheric humidity or water as carbon dioxide may be formed which, in closed containers can result in pressurization. Care should be taken when re-opening partly used containers.

Naked flames and smoking should not be permitted in storage areas. It is recommended that fork lift trucks and electrical equipment are protected to the appropriate standard.

Persons with a history of asthma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this preparation is used.

Examination of lung function should be carried out on a regular basis on persons applying this preparation.

Incompatible materials: Contact with water will cause this product to cure. Incompatible with acids, bases, and oxidizers

Recommended storage range is less than 90°F.

See section 2 for further details. - [Storage]:
Specific end use(s)
No data available.

VIII. EXPOSURE CONTROLS / PERSONAL PROTECTION

CAS No. Ingredient Source Value
0000100-41-4 Ethyl Benzene OSHA
ACGIH
NIOSH
TWA 100 ppm (435 mg/m3)STEL 125 ppm
TWA: 20 ppm2B, Revised 2011,
TWA 100 ppm (435 mg/m3) ST 125 ppm (545 mg/m3)
0000101-68-8 Diphenylmethanediisocyanate OSHA
ACGIH
NIOSH
C 0.2 mg/m3 (0.02 ppm)
TWA: 0.005 ppm Ceiling: 0.01 ppmSkin, S
TWA 0.05 mg/m3 (0.005 ppm) C 0.2 mg/m3 (0.020 ppm) [10-minute]
0001330-20-7 Xylene OSHA
ACGIH
STEL 150 ppm
TWA: 100 ppm STEL: 150 ppm
0005873-54-1 Benzene, 1-isocyanato-2-[(4- isocyanatophenyl)methyl]- ACGIH
NIOSH
TWA: 1.o mg/m3Revised 2008,
TWA 10 mg/m3 (total) TWA 5 mg/m3 (resp)
0064742-47-8 Petroleum distillates, hydrotreated light Supplier Recommended 300 ppm PEL
Exposure controls
Respiratory
When concentrations exceed the exposure limits shown above workers must wear appropriate respirators approved in accordance with Directive 89/656/EEC and the Personal Protection Equipment Regulations. Provision of other controls such as exhaust ventilation should be considered if practical.
An air fed respirator must be worn when applying this product in a confined space. Even in open spaces, an air fed respirator should be worn when spraying. If applying by brush or roller in an open, well ventilated area, air fed respirators could be replaced by a charcoal filter mask.
Eyes
Chemical splash goggles (ANSI Z-87.1 or approved equivalent) and/or face shield. Have an eye wash station available.
Skin
Avoid all skin contact by covering as much of the exposed skin area as possible with appropriate clothing. Wear impervious gloves.
Engineering Controls
Provide adequate ventilation. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates and any vapor below occupational exposure limits suitable respiratory protection must be worn.
Persons with a history of asthma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this preparation is used.
Examination of lung function should be carried out on a regular basis on persons spraying this preparation.
Other Work Practices
Use good personal hygiene practices. Wash hands before eating, drinking, smoking or using toilet. Promptly remove soiled clothing and wash thoroughly before reuse.
See section 2 for further details. - [Prevention]:

IX. PHYSICAL AND CHEMICAL PROPERTIES

Property Value
Appearance Viscous Liquid
Odor Not Available
Odor Threshold Not Measured
pH Not Available
Melting / Freezing Point Not Available
Initial Boiling Point / Boiling Range 281 - 284°F
Flash Point 80°F
Evaporation Rate (Ether = 1) Slower than ether
Flammability (solid, gas) Not Applicable
Upper/lower flammability or explosive limits Upper: 7%
Lower: 1%
Vapor Pressure Not established
Vapor Density Not Available
Specific Gravity Not Available
Water Solubility Nil, reacts with water
Partition Coefficient: n-octanol/water Not Measured
Auto Ignition Temperature Not Established
Decomposition Temperature Not Available
Viscosity(cST) 2,000 - 4,000cps
VOC Content (%) Less than 250g/Liter
Density 8.8 - 9.2 pounds per gallon
%Volatile 19 - 23%(by weight)
Other information
No relevant information.

X. STABILITY AND REACTIVITY

Reactivity
May polymerize.
CHEMICAL STABILITY
Stable under normal circumstances.
POSSIBILITY OF HAZARDOUS REACTIONS
Reaction with water can create CO2.
CONDITIONS TO AVOID
No data available.
INCOMPATIBLE MATERIALS
Contact with water will cause this product to cure. Incompatible with acids, bases, and oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS
Will not occur if properly handled and stored.

XI. TOXICOLOGICAL INFORMATION

Acute toxicIty

Exposure to solvent vapor concentrations from the component solvents in excess of the stated occupational exposure limits may result in adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the kidneys, liver and central nervous system. Symptoms include headache, nausea, dizziness, fatigue, muscular weakness, drowsiness and in extreme cases, loss of consciousness.

Repeated or prolonged contact with the preparation may cause removal of natural fat from the skin resulting in dryness, irritation and possible non-allergic contact dermatitis. Solvents may also be absorbed through the skin. Splashes of liquid in the eyes may cause irritation and soreness with possible reversible damage.

Based on the properties of the isocyanate content of this product, respiratory exposure may cause acute irritation and/or sensitization of the respiratory system resulting in asthmatic symptoms, wheezing and a tightness of the chest. Sensitized persons may subsequently show asthmatic symptoms when exposed to airborne concentrations of isocyanates well below the occupational exposure limit. Repeated exposure may lead to permanent respiratory disability.

Ingredient Oral LD50, mg/kg Skin LD50, mgkg Inhalation Vapor LC50 mg/L/4hr Inhalation Dust/Mist LC50, mg/L/4hr Inhalation Gas LC50, ppm
Polyoxypropylene glycol
25322-69-4
2,000.00 Rat-Category: 4 No data available No data available No data available No data available
Xylene
1330-20-7
4,299.00 Rat-Category: 5 1,548.00,Rabbit-Category: 4 No data available 20.00, Rat-Category: NA 5,000.00, Rat-Category: 4
Diphenylmethanediisocyanate - (101-68-8)
4,700.00, Rat - Category: 5 No data available No data available



No data available


No data available
Chlorinated paraffin c22-30 - (63449-39-8) 11,700.00, Rat - Category: NA No data available No data available No data available No data available
Aluminium hydroxide - (21645-51-2) 5,000.00, Rat - Category: 5
No data available No data available No data available No data available
Polymeric Diphenylmethane Diisocyanate - (9016-87-9) 49,000.00, Rat - Category: NA 9,400.00, Rabbit
Category: NA

No data available No data available No data available

Ethyl Benzene - (100-41-4)

3,500.00, Rat - Category: 5 15,433.00, Rabbit
Category: NA

17.20, Rat - Category: 4 No data available 4,000.00, Rat - Category: NA
Petroleum distillates, hydrotreated light - (64742-47-8)
> 5,000.00, Rat - Category:
NA

>2,000.00, Rabbit
Category: 5

No data available No data available No data available


Note

When no route specific LD50 data is available for an acute toxin, the converted acute toxicity point estimate was used in the calculation of the product's ATE (Acute Toxicity Estimate).

CARCINOGEN DATA

The table below indicates whether each agency has listed any ingredient as a carcinogen.

CAS No. Ingredient Source Value
0001309-64-4 Antimony trioxide IARC Group 2b: Yes
0000101-68-8Diphenylmethanediisocyanate
IARC
Group 3: Yes
0001330-20-7XyleneIARCGroup 3: Yes
0009016-87-9Polymeric Diphenylmethane DiisocyanateIARCGroup 3: Yes
0063449-39-8 Chlorinated paraffin c22-30 NTP Suspected: Yes

XII. ECOLOGICAL INFORMATION

Toxicity
See Section 3 for chemical specific data.
Aquatic Ecotoxicity
Ingredient 96 hr LC50 fish, mg/l 48 hr EC50 crustacea, mg/l ErC50 algae mg/l
polyoxypropylene glycol - (25322-69-4) 650.00, Menidia beryllina Not Available Not Available
Xylene - (1330-20-7) 3.30, Oncorhynchus mykiss 8.50, Palaemonetes pugio 100.00 (72 hr), Chlorococcales
Diphenylmethanediisocyanate - (101-68-8) Not Available 129.70, Daphnia magna Not Available
Chlorinated paraffin c22-30 - (63449-39-8) 300.00, Lepomis macrochirus 102.00, Daphnia magna Not Available
Ethyl Benzene - (100-41-4) 4.20, Oncorhynchus mykiss 2.93, Daphnia magna 3.60 (96 hr), Pseudokirchneriella subcapitata
Petroleum distillates, hydrotreated light - (64742-47-8) 45.00, Pimephales promelas 4,720.00, Dendronereides heteropoda Not Available
PERSISTENCE AND DEGRADABILITY
There is no data on the preparation itself
BIOACCUMULATIVE POTENTIAL
Not measured.
MOBILITY IN SOIL
No information available.
RESULTS OF PBT AND VpvB ASSESSMENT
This product contains no PBT/vPvB chemicals.
OTHER ADVERSE EFFECTS
An environmental hazard cannot be excluded in the event of unprofessional handling or disposal.
Potentially toxic to aquatic life.

XIII. DISPOSAL CONSIDERATIONS

Waste treatment methods
Observe all federal, state and local regulations when disposing of this substance.

XIV. TRANSPORT INFORMATION

DOT (Domestic Surface Transportation) IMO / IMDG (Ocean Transportation) ICAO/IATA
UN number UN1263 UN1263 UN1263
UN proper shipping name UN1263, Paint, 3, III Paint Paint
Transport hazard class(es) DOT Hazard Class: 3 IMDG: 3
Sub Class: Not Applicable
Air Class: 3
Packing group III III III
Enviromental hazards
IMDG
Marine Pollutant: Yes
Special precautions for user
No further information

XV. REGULATORY INFORMATION

Regulatory Overview
The regulatory data in Section 15 is not intended to be all-inclusive, only selected regulations are represented
Toxic Substance Control Act (TSCA)
All components of this material are either listed or exempt from listing on the TSCA Inventory
WHMIS Classification
D2A
US EPA Tier II Hazards
Fire: Yes
Sudden Release of Pressure: No
Reactive: No
Immediate (Acute): Yes
Delayed (Chronic): Yes
EPCRA 311/312 Chemicals and RQs(lbs):
Diphenylmethanediisocyanate ( 5,000.00)
Ethyl Benzene (1,000.00)
Xylene: (100.00)
EPCRA 302 Extremely Hazardous
To the best of our knowledge, there are no chemicals at levels which require reporting under this statute.
Sara 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical or chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372:
Chemical name CAS - No Weight% SARA 313 - Threshold Values %
Xylene 1330-20-7 10 - 30 1.0
Ethyl benzene 100-41-4 7 - 13 .1
Supplier Trade Secret 5 - 10 1.0
Methylene bisphenyl isocyanate (MDI) 101-68-8 1 - 5 1.0
SARA 311/312 Hazard Categories
Acute Health Hazard: Yes
Chronic Health Hazard: Yes
Fire Hazard: Yes
Sudden Release of Pressure Hazard: No
Reactive Hazard: No
CWA (Clean Water Act)
This product contains the following substances which are regulated pollutants pursuant to the Clean Water Act (40 CFR 122.21 and 40 CFR 122.42):
Chemical Name CWA - Reportable Quantities CWA - Toxic Pollutants CWA - Priority Pollutants CWA - Hazardous Substances
Xylene
1330-20-7
100 lb X
Ethyl benzene
100-41-4
1000 lb X X X
CERCLA

This material, as supplied, contains one or more substances regulated as a hazardous substance under the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) (40 CFR 302):

Chemical NameHazardous Substances RQsExtremely Hazardous Substances RQsRQ
Xylene 1330-20-7100lbRQ= 100 lb final RQ, RQ= 45.4 kg final RQ
Ethyl Benzene 100-41-41000lbRQ 1000 lb final RQ, RQ 454 kg final RQ
Methylene bisphenyl isocyanate (MDI)5000lbRQ 5000 lb final RQ, RQ 2270 kg final RQ
U.S State Regulations
California Proposition 65
This product contains the following Proposition 65 chemicals:
Chemical NameCalifornia Prop. 65
Ethyl Benzene 100-41-4Carcinogen
New Jersey RTK Substances (>1%):
Aluminum(AL)
Diphenylmethanediisocyanate
Ethyl Benzene
Polymeric Diphenylmethane Diisocyanate
Xylene
Pennsylvania RTK Substances (>1%):
Aluminum (Al)
Diphenylmethanediisocyanate
Ethyl Benzene
Xylene
U.S. State Right-to-Know Regulations
Chemical NameNew JeseyMassachusettsPennsylvaniaRhode IslandIllinois
Xylene 1330-20-7XXXXX
Ethyl Benzene 100-41-4XXXXX
Supplier Trade SecretXXXX
Polymethylene polyphenylene isocyanate 9016-87-9XX
Methylene bisphenyl isocyanate (MDI) 101-68-8XXXXX
International Regulations
Mexico
National Occupational Exposure Limits
ComponentExposure Limit
Xylene 1330-20-7 (10-30)Mexico: TWA= 100 ppm
Mexico: TWA= 435 mg/m3
Mexico: STEL= 150 ppm
Mexico: STEL= 655 mg/m3
Ethyl Benzene 100-41-4(7-13)Mexico: TWA 100 ppm
Mexico: TWA 435 mg/m3
Mexico: STEL 125 ppm
Mexico: STEL 545 mg/m3
Supplier Trade Secret(5-10)Mexico: TWA= 10 mg/m3
Methylene bisphenyl isocyanate (MDI) 101-68-8(1-5)Mexico: TWA 0.02 ppm
Mexico: TWA 0.2 mg/m3
Mexico: TWA 0.005 ppm
Mexico: TWA 0.051 mg/m3
Mexico - Occupational Exposure Limits - Carcinogens
Canada
WHMIS Hazard Class
D2A - Very toxic materials
D2B - Toxic materials
B2 - Flammable liquid

XVI. OTHER INFORMATION

The information and recommendations contained herein are based upon data believed to be correct. However, no guarantee or warranty of any kind, expressed or implied, is made with respect to the information contained herein. We accept no responsibility and disclaim all liability for any harmful effects which may be caused by exposure to our products. Customers/users of this product must comply with all applicable health and safety laws, regulations, and orders.

This is the first version in the GHS SDS format. Listings of changes from previous versions in other formats are not applicable.

Judgments as to the suitability of information herein for the purchaser’s purposes are necessarily the purchaser’s responsibility. Although reasonable care has been taken in the preparation of such information, Aldo Products Company, extends no warranties, makes no representations, and assumes no responsibility as to the accuracy or suitability of such information for application to the purchaser’s intended purpose or for consequences of its use.

The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.