EnergyGuard Acrylic Clear Coating

Membrane Roofing / Fluid Applied Roofing / Elastomeric Roof Coating - 075600

Product Name

EnergyGuard
Acrylic Clear Coating

Manufacturer
Lexis Coatings
  • 6460 Hwy 92 Ste 100
  • Acworth, GA 30102
Phone: 770-755-1820
Hours: Mon - Fri 8am - 5pm
EnergyGuard Acrylic Clear Coating
Product Description

EnergyGuard Acrylic Clear Coat is a water-based, single component, acrylic roof coating. It is designed to restore and protect fiberglass skylights or improve the dirt pick up resistance of our white acrylic roof coatings.

  • Provides a seamless, elastic and durable membrane.
  • Extends the life of fiberglass skylights.
  • Superior adhesion to brick, stucco and masonry surfaces.
  • Enhances dirt pickup resistance when used over elastomeric roof coatings.
  • Easy to use, non-toxic and VOC-compliant.
Technical Data
  • See table on the following page.
Installation
  • Ready to use. Thinning is not necessary. Mix well before using.
  • Roof must be clean, dry and free of any oil, grease, dirt or loosely adhered coating. Bare surfaces must be prepared and checked for compatibility.  
  • Follow our roof restoration procedures and always perform an adhesion test.
  • Equipment: polyester brush, roller or 3000psi, 2gpm airless sprayer with a .017 tip. Do not leave coating in spray guns, hoses and pumps for prolonged periods.
Availability & Cost

EnergyGuard Acrylic Clear Coating is available directly from Lexis Coatings and our authorized distributors.

Warranty

On pre-qualified and registered applications completed by Lexis-approved contractors, long term warranties are available. Contact Lexis Coatings for warranty information.

Maintenance

Read our Care and Maintenance Guidelines.

Technical Services

Contact Lexis Coatings for technical support.

Filing Services

Additional product information is available from Lexis Coatings.


csi This product data sheet conforms to the editorial style prescribed by The Construction Specifications Institute.
The manufacturer is responsible for technical accuracy.

EnergyGuard Acrylic Clear Coating Technical Data

Property Value Method
Clean UpWater
ColorSlightly translucent
Coverage0.4g/100SF - 0.6g/100SF depending on surface porosity.
Elongation300%
Flash PointNone
Hardness60 Shore A
Packaging5 gallon pail
Shelf Life12 months @ 40°-90° F
Solids by Volume40%ASTM D-2697
Solids by Weight43.5%ASTM D-1644
Tensile Strength1400 psi
Viscosity2,000 ± 500 cP

Caution: EnergyGuard Acrylic Clear Coating is a water-based product which will freeze and become unusable at temperatures below 32°F. Suspend all application if conditions prevent a complete cure before sunset, rain, fog, dew or freezing temperatures. Lexis Coatings must be completely dry before exposing to water or foot traffic. Keep Lexis Coatings containers covered when not in use. Dispose of all containers in accordance with state and local environmental regulations. Keep away from children. If ingested, DO NOT induce vomiting. Call physician immediately.

Product information contained herein are presented in good faith and believed to be reliable. They do not constitute part of our terms and conditions of sale. It is also not a guarantee, either expressed or implied, that the data are correct or that products described are merchantable or fit for a particular purpose as methods of use are beyond our control. Customer should determine the suitability of our materials and installation recommendations before usage. Manufacturer's sole responsibility shall be to replace that portion of any product that proved to be defective.


csi This product data sheet conforms to the editorial style prescribed by The Construction Specifications Institute.
The manufacturer is responsible for technical accuracy.

Roof Coating Calculator

Enter the coverage area in square feet.

sf
mils
gal/100SF
Gallons
Pails
EnergyGuard Acrylic Clear Coating
5 Gallon Pail Clear

173.00

Resources

Safety Data Sheet